An IoT solution for extending your laptop battery's life.
ion is a command line program, used to interact with a smart plug to easily control your battery's charge cycles. Research shows that cycling your batteries charge level between 30% and 75% (rather than 0%-100%) can greatly extend its service life, which is good for your wallet and for the environment.
Contributions welcomed! We'd love for you to get involved. Just submit a pull request or open an issue.
You will need a smart plug (any will do, as long as it's supported by IFTTT. (Note: if your smart plug is not supported by IFTTT you may still be able to use our software to activate/deactivate it, but this isn't covered in this guide)).
You can install ion wherever you like, but we recommend creating a new directory for it in your home folder. To do so, type the following command into your terminal or command prompt:
mkdir ~/.ionNow, navigate into this new directory:
cd ~/.ion... and install the repository with git (follow these instructions to install git if you don't have it):
git clone https://github.com/tomcobley/ionThis should have created a new directory within your current directory called ion. Navigate into it and take a look around with:
cd ion
lsDepending on your operating system (currently most versions of MacOS and Linux are supported), you may need to execute one of the following commands:
brew install curlIf you don't have brew already (you should, it's good), follow the instructions here to install it.
sudo apt-get install libcurl4-gnutls-devYou have now installed the code and dependencies, and are ready to proceed with the next section.
Make sure you're in the ion directory that was created in the previous step. If you're not, move back there with:
cd ~/.ion/ionTo compile the code, run:
makeNext, run:
./setup.shThis will create a shell script called /usr/local/bin/ion, which can be used to run the program.
Next, you need to create an applet on IFTTT. To do so, create an IFTTT account. Once you have done this, click the icon in the top right corner, then click Create to create an applet.
Click on 'This' to add a trigger signal. On the 'Choose a service' page, search for and select the service called 'Webhooks', then on the 'Choose trigger' page, click 'Receive a web request'. Write a name for the event (we recommend "charge_low") and select Create trigger.
Now click on the 'That' button to choose an action. Search for the brand of smart plug that you have, and select the relevant option. If you haven't already set up your smart plug, you should do that now, following the manufacturer's instructions. You may have to log in to your account with the smart plug manufacturer to link your smart plug. It is important that you link this "charge_low" action with the turning on of the smart plug. This action will be triggered when the charge of your laptop becomes low, turning on your laptop charger.
Repeat the above process, creating a new applet, this time with the event name "charge_high", and the action being the turning off of the same smart plug. This action will be triggered when the charge of your laptop becomes high, turning off your laptop charger.
Now, find out your maker webhook key, by visiting this page. Under Account Info, you will see your URL, something like https://maker.ifttt.com/use/xxxxxxxxxxx-xxxxxxxxxx, where the section following the last / is your unique webhook key. Save this key for later.
To configure your settings, run:
ion initYou will now be able to enter the URLs used to trigger your IFTTT applets:
Your first response should as follows, but with EVENT_NAME replaced by charge_low (or whatever name you used when creating your first webhook), and xxxxxxxxxxx-xxxxxxxxxx replaced by your webhook key:
https://maker.ifttt.com/trigger/EVENT_NAME/with/key/xxxxxxxxxxx-xxxxxxxxxx
Your second response should be the same, but with EVENT_NAME replaced by charge_high (or whatever name you used when creating your second webhook).
For the charge lower and upper bounds, we recommend you use the provided system defaults.
You should now be able to manually run the program, give it a try with:
ionYou should also be able to run the test suite to check everything has been set up correctly. Try it with:
cd tests
make runtestsIt is specifically important that the webhook tests pass. Moreover, make sure that the plug turns ON and then OFF when the test is running. Otherwise, you may have configured your IFTTT tasks incorrectly.
Also, feel free to test if the program is interfacing with the smart plug correctly by adjusting the lower and upper bounds so your current battery percentage is outside the range you specified.
Keep following the steps to get the program to run automatically rather than manually.
We need to add a cron job, which will run the program once a minute (important to keep an eye on your battery level). Run:
crontab -eYou may get a message asking you to pick an editor. Pick your favourite, or Nano (the easiest). Now add the following line to the file and exit the editor:
* * * * * /usr/local/bin/ionIf you're on a Mac, you may get a popup saying Terminal would like to administer your computer, click OK.
This will run the shell script we created earlier (which runs ion) once per minute.
That's it! The program should now keep your laptop battery within the range you specified, keeping your battery healthy for longer. If you have any problems, please submit an issue on GitHub.
ion was developed by Tom Cobley, Andrew Elkadi, Dimitri Chamay and Nicholas Duer.