| 1: Stock V-Wheels | 2: MGN-12H | 3: Dual Z (Wheels and MGN) |
|---|---|---|
 |
 |
 |
Please visit my website to start the Config Finder. I have spent many hours creating a very interactive and easy to follow guide for the mod. You will get all the files you need at the end of the Config Finder, including a zip file with all the STLs, materials you need, and the instructions for your particular setup.
If you have any questions feel free to join the Discord-Server
All my work is 100% Open-Source and free for everyone to use. But designing and developing all these mods takes a lot of time and effort, so if you appreciate my work and would like to support it and also help cover the costs of gettings the mods perfect, you can use one of the following links. Thanks a lot 🤍
This mod now exists in the 3rd version (V3). The _ignore folder contains all the files for the old versions (V1 and V2). The current version (V3) exists in 3 variations:V-Wheels, MGN-12h and Dual Z (Dual Z works with both variants V-Wheels and MGN-12h). In addition, you can choose between the normal and ultralow version. I hope this clarifies the confusion between the versions and variants. Again please use the config finder on my website to configure your individual setup.
I'm not an expert and 3D printing is my hobby. So please be careful when you rebuild this mod and don't just go ahead. For my printer the parts fit perfectly. Everybody bears the risks of a modification himself. All parts can be modified as you like. :D
All Parts can be printed without support. Keep the orientation for best results. Yes, you can use PLA but no, you shouldn’t use PLA. I used PETG for the unenclosured, ABS for the enclosured printer. Suggested print settings: 50% Infill, 5 Walls/Top-Bottom layer. Good luck and happy printing!
My Ender 3 always had problems with the Z-axis, which were caused by a bent and misaligned leadscrew. Therefore I decided to convert the Ender to belts in Z as well. This mod also solves the problem of a hanging x-axis on the right side. Because of the two belts, both sides run synchronously and can also be adjusted very precisely.
This mod can't solve problems that are caused by an inconsitent extrusion. Inconsitent extrusion means an untuned Flowrate/Extrusion multiplier and causes very inconsitent layers --> this looks like the picture below. To get rid of that you should tune all extrusion related values, like Flowrate an Linear Advance (Marlin) / Pressure Advance (Klipper). Take a look at this tuning guide, its very well made (Works also for non Voron Printers and Marlin machines).
I am very very proud to announce that there is now a Motion Kit for this mod available for purchase! The Motion Kit from Powge provides all parts for Single Z or Dual Z, with F623 or 20T Idlers and in black or silver. This allows us to use high quality parts at a low price! Belts and pulleys match up perfectly and make the mod a little better. Thanks to Powge for this opportunity! (btw Aliexpress shows delivery times of several months, but shipping is significantly faster (to Germany it takes about 10 days)). Link to the kit (also included in the BOM): https://www.aliexpress.com/item/1005003933709487.html
There's a reason I haven't made a rail version in a very long time: Rails are not better than rollers in terms of quality. At least the cheap rails you can buy on AliExpress. The tolerances are not good, they don't last long and can give z artifacts that you don't have with rollers. From time to time I get messages that the x axis drops as soon as the power is turned off. Every time that happens the mod uses rails. And like almost of those has cheap china rails. The problem with these cheap rails is that there is no friction at all, no tension and the Z axis is very poorly guided. The little Z motor has to carry all the weight because the rails are so loose they can't take any load. You also have to take care of the rails, lubricate and clean them from time to time, and make sure they don't leak. So you will spend a lot of money on a set of rails if you want good rails. Plus lubricants, cleaners, etc. Also, mounting the rails is more complicated. With wheels, you spent almost nothing on a new wheel, put it on, and you are good to go. So I recommend trying wheels first and if you still want rails, you just need to print two small adapters to install the rails. Keep things simple ;)
You have to remove the flage of the toothed idlers, otherwise they would get in contact with the profile.
I would like to thank everyone who supported this project, especially Guffy and the Awesome Helpers from my Discord! Also a big thank you to my mate Deutherius who helped me with the initial setup of this mod!
This mod uses a modified transmission from the Voron 2.2. I made a different frame to mount it on the Ender 3. The tensionerarm and the tensionerring are from the Voron guys. These aren’t my work!!! The mount and the 80T gear are made by myself. Because the parts will be updated regularly, you can find the STLs I used on GitHub
I want to thank everyone who has helped me over the last months with feedback, support and confidence. Without you this mod would not have become sich a thing! Thanks also to Creality for the Golbal DIY Contest. I am very proud to announce that I could reach the 3rd place with his mod.
Keybak system similar to the Switchwire design. The files were remixed from the Switchwire CAD file. For licensing reasons, all Keybak files are uploaded to GitHub only! Idea from Voron team, thanks!
Info: Because of the transmission it is not necessary to install a Keybak system. The 1:5 ratio increases the holding force of the motor so that it can hold the X axis up even when it is powered off. A correctly adjusted belt tension is important for this. If you are using the V-Wheels it is also important that they are installed correctly (See Troubleshooting). From time to time I hear that users struggle to keep the axis up by using the belt tension only. Therefore, I have designed the Keybak system. See BOM for all the parts you need.
What is a Keybak system and what is it for? A Keybak is actually used to secure keys to a wire rope. Depending on the Keybak, they can support a lot of weight without the cord extending on its own. The Keybak used here is strong enough to support the x axis. It takes the load off the motor and shares the weight of the axis with it. It is still important to tension the belts properly! If the belts are not tightened enough, there will be unclean prints later! So make sure that the Keybak doesn't mislead you into not tightening the belts enough. See my FAQ video on how to properly tension the belts (video coming soon).
You will have to print a new 1_LeftTop_A and a 3_spacer to use the Keybak.
NO! You do not have to change anything in the firmware. This modification works with the stock board and stock firmware.
Yes and no. All parts should work with PLA, except the motor tensioner arm. The motor has to hold more weight now, so the motor could get warm. Since PLA deforms at ~40°C you should keep an eye on your motor (see troubleshooting). Because of that I would recommend PETG. When you're printing inside an enclosure you should use ABS. Try Esun ABS+, super easy to print, and much stronger than PETG.
YES! You can use this mod with all Ender 3 versions.
View the makes on Thingiverse. Some of you made a CR build so I thing it should fit. Feel free to give some feedback about that.
NO! A cheap aluminium or "normal" steelrod is just fine. There's also a transmission (rotated and unrotated) that hold a bearing inside, so you have some extra support in the middle of your rod. You also could use your leadscrew to minimize the costs.
So you want to use two stepper motors to have an indipendent z axis? Thats possible of course! Just use the files from the Dual Z folder! See BOM for detailed parts list.
Yes of course! I'm happy to help, so please contact me via Discord (kevinakasam#2097). I'm sure we will find a solution for your problem :)
Thank you very much if you want to support my work! But please dont feel obligated to do so. All parts are free and open source and will stay that way! If you still want to support me, you can find a donation link at the bottom of this page. Really many many thanks! :)
Thats a quick fix. Just remove all the pins in you motor connector that goes into the mainboard (like I showed you in my video) and insert them in the opposite order (4321 instead of 1234).
First of all: A warm or slighty hot motor isn't a super bad thing. But you should change that. Try to lower your V-ref/Amps till the motor stays hand warm. But be careful to not reduce the current too much, or your motor will lose steps. The stock Z motor is very small so it's a big job for the tiny motor. Don't worry if your motor gets warm.
Probably the most asked question, but I can promise that your axis does not have to drop! As already mentioned, the z motor is very small. Therefore the magnetic field that exists in the motor even without power isn't very strong. But it's strong enough to keep the axis up.
- You are using the original V-Rollers? Be sure they are properly set up. Turn the eccentric nut until the rollers are in contact with the profile. Put a little tension on the rollers, but not too much! Do not risk a flat spot of your rollers. The tension is correct when they are tight, and you can't turn them with your finger in the same place, but the axis moves when you turn the rollers.
- You have no rollers or your axis is still dropping? Tension your long belts a little more. Increase the tension until your axis stops dropping. Be careful not to break something. But the parts can take a lot of tension. Otherwise, check out my FAQ video about how to tension the belts (THE VIDEO HAS STILL TO BE CREATED).
- Tension the small looped belt a bit more as well. But very carefully! Usually the tension only needs to be high enough to keep the belt from slipping over the printed wheel. But you can increase the tension a little bit. But not too much, otherwise the motor can't turn anymore.
- That sounds too complicated? Your motor is also too hot? A solution would be a bigger motor, like the one on the X and Y axis. A bigger motor is able to hold the axis up very easily, with less tension and less heat. But as I said, this is not necessary, it also works with the original motor.
- New solution: Install the Keybak System (added 31.10.2021).
25.02.2023: Update? It's been a while! Release of the V3.7 files.
- Plate update
-The right plate got an extra hole to access the M4 screw that holds the metal plate to the X axis.
- The holes for the hex nut got a bridging pattern so no more filament can curl there.
- Transmission Update
- All the transmission bodies got a cutout to make it easier to tighten the motor shaft grub screw.
- Utralow and Dual Z transmissions have also received a hole to access the 20T pulley grub screws.
- Update of the lower parts
- The small hill that holds the 3x14mm pin in place is now much smaller and it should be much easier to insert the pins
- V3_Extras update
- Added a version with heat inserts that replaces the M3 hex nuts with heat inserts.
- MGN 12C support
- Printer adaptations for Artillery Hornet and Tevo Tarantula Pro
21.09.2022: Release of the Website and the new instructions!
23.08.2022: Big Update! Release of the V3.6 files.
- Almost all Parts got an update:
- Housing for the tensioner on the plates is thicker now
- Bottom Parts use Pins now instead of M3 screws (old files still available in
\V3\_old_V3_partsin case you want to use screws) - Replaced printed thread on the transmission tensioner with a M5 Screw
- EOL for unrotated and non-exttra bearing transmission
- Revomed the top holes from the transmissions and Top part --> less hardware needed and it was a pain to install these, sorry for that!)
- The UltraLow version is now an "official" variattion of this mod (no longer in the V3_extras folder).
- Things that will follow:
- New Instructions with an updated BOM --> Interactive with a ton of information
14.07.2022: Added MGN 9H support in the V3_Extras folder.
09.05.2022: Updated the BOM. (16T link was wrong, sorry for that!)
27.01.2022: Updated the BOM.
19.01.2022: Small Changes
- Added the V3_Extra folder to store the customizations I made for you.
- Added the small hole in the V3.5 plates again for the belt from the tensioner block.
09.01.2022: Second big Update: V3.5
- Adjusted the Belt path so they're parallel now. This was requested quite often, sorry it took so long.
- Added a version for toothed bearings.
- Added Dual Z Version.
- Removed upper holes in the Top parts, so you do not have to unscrew the top profile.
31.10.2021: Big Update!
- Moved the extruder to the stock position for the V3.4_Bowden plates (Fits BMG now too). Idea from trohnjavolta, thanks!
- Split the tops into two parts to make them easier to print and more stable (Top_A and Top_B). Idea from sztywniutko (Thing:4911634), thanks!
- Added a PSU mount.
- Added a Keybak system similar to the Switchwire design. The files were remixed from the Switchwire CAD file. For licensing reasons, all Keybak files are uploaded to GitHub only! Idea from Voron team, thanks!
17.08.2021: Made some small tolerance changes to the rotated transmission and the inner M3 parts.
31.07.2021: I made a mistake and uploaded the wrong files for "LeftTop" and RightTop". If you downloaded the files from Thingiverse between 15.06.2021 and 31.07.2021, please download the latest version. I am very sorry! Thanks to mbarryton for the hint!
15.06.2021: Important!!! Both Versions (rotated and unrotated) are compatible now. Both versions now have the identical LeftTop and RightTop (the one from the rotated version).
15.06.2021: I have added a version of both transmissions that include a ball bearing. So the rod is supported in the middle by another ball bearing.
15.06.2020: Updated CAD with all Versions. Many thanks to Regulus who did a great job adding many wonderful details to the CAD file. All parts are now properly aligned, all fasteners are added and named. Seriously many many thanks!
02.06.2021: Added Left and Right V3.3. Changed the design of the lower clamp profile. If youre using the 3.1 or 3.2 that's totally fine;)
02.06.2021: Updated the 80T Gear on GitHub. reduced the outer diameter a bit so theres a bigger gap to the profile. Thanks to Regulus!
06.05.2021: Modified MGN Version fits now for Ender 3 (Pro) and Ender 3 V2. Bowden Version tested. Thanks to Jon!
04.05.2021: Added a Video Tutorial.
02.05.2021: Added Left and Right V3.2. Tensioner were missaligned by ~0.5mm. Thanks to Zardozer for the hint! If youre using the old V3.1 its totally fine. I'm using them as well:D
14.02.2021: Changes for the MGN Version!! LeftV1 added. Please print 1_Left and 1_LeftV1. I would appreciate feedback for Left or LeftV1. I have created the files with the official CAD, but the M4 screws differ in the position by 2mm. Please print both versions and tell me which fits, thanks:)
26.02.2021: Added Bowdenversion.
26.02.2021: Started Changelog.
Donation Link: https://www.buymeacoffee.com/kevinakasam or via Paypal
