rotator_settings.h

/* -------------------------- rotation settings ---------------------------------------*/

#define AZIMUTH_STARTING_POINT_DEFAULT 180      // the starting point in degrees of the azimuthal rotator
                                                
//#define AZIMUTH_ROTATION_CAPABILITY_DEFAULT 450 // the default rotation capability of the rotator in degrees
#define AZIMUTH_ROTATION_CAPABILITY_DEFAULT 360
                                                
#define ELEVATION_MAXIMUM_DEGREES 180           // change this to set the maximum elevation in degrees

/* --------------------------- Settings ------------------------------------------------

You can tweak these, but read the online documentation!

*/

// analog voltage calibration - these are default values; you can either tweak these or set via the Yaesu O and F commands (and O2 and F2)....
#define ANALOG_AZ_FULL_CCW 4
#define ANALOG_AZ_FULL_CW 1009
#define ANALOG_EL_0_DEGREES 2
#define ANALOG_EL_MAX_ELEVATION 1018  // maximum elevation is normally 180 degrees unless change below for ELEVATION_MAXIMUM_DEGREES

#define ANALOG_AZ_OVERLAP_DEGREES 540         // if overlap_led above is enabled, turn on overlap led line if azimuth is greater than this setting
                                              // you must use raw azimuth (if the azimuth on the rotator crosses over to 0 degrees, add 360
                                              // for example, on a Yaesu 450 degree rotator with a starting point of 180 degrees, and an overlap LED
                                              // turning on when going CW and crossing 180, ANALOG_AZ_OVERLAP_DEGREES should be set for 540 (180 + 360)
#define OPTION_OVERLAP_LED_BLINK_MS 100                                             

// PWM speed voltage settings
#define PWM_SPEED_VOLTAGE_X1  64         // 0 to 255
#define PWM_SPEED_VOLTAGE_X2  128        // 0 to 255
#define PWM_SPEED_VOLTAGE_X3  191        // 0 to 255
#define PWM_SPEED_VOLTAGE_X4  253        // 0 to 255

//AZ
#define AZ_SLOWSTART_DEFAULT 0            // 0 = off ; 1 = on
#define AZ_SLOWDOWN_DEFAULT 0             // 0 = off ; 1 = on
#define AZ_SLOW_START_UP_TIME 2000        // if slow start is enabled, the unit will ramp up speed for this many milliseconds
#define AZ_SLOW_START_STARTING_PWM 1      // PWM starting value for slow start (must be < 256)
#define AZ_SLOW_START_STEPS 20            // must be < 256


#define SLOW_DOWN_BEFORE_TARGET_AZ 10.0  // if slow down is enabled, slowdown will be activated within this many degrees of target azimuth
#define AZ_SLOW_DOWN_PWM_START 200         // starting PWM value for slow down (must be < 256)
#define	AZ_SLOW_DOWN_PWM_STOP 20          // ending PWM value for slow down (must be < 256)
#define AZ_SLOW_DOWN_STEPS 200 //20       // must be < 256
#define AZ_INITIALLY_IN_SLOW_DOWN_PWM 50  // PWM value to start at if we're starting in the slow down zone (1 - 255)

//EL
#define EL_SLOWSTART_DEFAULT 0            // 0 = off ; 1 = on
#define EL_SLOWDOWN_DEFAULT 0             // 0 = off ; 1 = on
#define EL_SLOW_START_UP_TIME 2000        // if slow start is enabled, the unit will ramp up speed for this many milliseconds
#define EL_SLOW_START_STARTING_PWM 1      // PWM starting value for slow start  (must be < 256)
#define EL_SLOW_START_STEPS 20            // must be < 256

#define SLOW_DOWN_BEFORE_TARGET_EL 10.0  // if slow down is enabled, slowdown will be activated within this many degrees of target elevation
#define EL_SLOW_DOWN_PWM_START 200         // starting PWM value for slow down (must be < 256)
#define	EL_SLOW_DOWN_PWM_STOP 20          // ending PWM value for slow down (must be < 256)
#define EL_SLOW_DOWN_STEPS 20
#define EL_INITIALLY_IN_SLOW_DOWN_PWM 50  // PWM value to start at if we're starting in the slow down zone (1 - 255)

#define TIMED_SLOW_DOWN_TIME 2000

//Variable frequency output settings - LOWEST FREQUENCY IS 31 HERTZ DUE TO ARDUINO tone() FUNCTION LIMITATIONS!
#define AZ_VARIABLE_FREQ_OUTPUT_LOW   31     // Frequency in hertz of minimum speed
#define AZ_VARIABLE_FREQ_OUTPUT_HIGH 5000 //100    // Frequency in hertz of maximum speed
#define EL_VARIABLE_FREQ_OUTPUT_LOW   31     // Frequency in hertz of minimum speed
#define EL_VARIABLE_FREQ_OUTPUT_HIGH 100    // Frequency in hertz of maximum speed

// Settings for OPTION_AZ_MANUAL_ROTATE_LIMITS
#define AZ_MANUAL_ROTATE_CCW_LIMIT 0   // if using a rotator that starts at 180 degrees, set this to something like 185
#define AZ_MANUAL_ROTATE_CW_LIMIT 535  // add 360 to this if you go past 0 degrees (i.e. 180 CW after 0 degrees = 540)

// Settings for OPTION_EL_MANUAL_ROTATE_LIMITS
#define EL_MANUAL_ROTATE_DOWN_LIMIT -1
#define EL_MANUAL_ROTATE_UP_LIMIT 181

// Speed pot settings
#define SPEED_POT_LOW 0
#define SPEED_POT_HIGH 1023
#define SPEED_POT_LOW_MAP 1
#define SPEED_POT_HIGH_MAP 255

// Azimuth preset pot settings
#define AZ_PRESET_POT_FULL_CW 0
#define AZ_PRESET_POT_FULL_CCW 1023
#define AZ_PRESET_POT_FULL_CW_MAP 180         // azimuth pot fully counter-clockwise degrees
#define AZ_PRESET_POT_FULL_CCW_MAP 630        // azimuth pot fully clockwise degrees

#define ENCODER_PRESET_TIMEOUT 5000

// various code settings
#define AZIMUTH_TOLERANCE 3.0            // rotator will stop within X degrees when doing autorotation
#define ELEVATION_TOLERANCE 0.1 //1.0
#define OPERATION_TIMEOUT 120000        // timeout for any rotation operation in mS ; 120 seconds is usually enough unless you have the speed turned down
#define TIMED_INTERVAL_ARRAY_SIZE 20

#define CONTROL_PORT_BAUD_RATE 9600
#define REMOTE_UNIT_PORT_BAUD_RATE 9600
#define GPS_PORT_BAUD_RATE 9600
#define GPS_MIRROR_PORT_BAUD_RATE 9600
#define CONTROL_PORT_MAPPED_TO &Serial  // change this line to map the control port to a different serial port (Serial1, Serial2, etc.)
//#define REMOTE_PORT_MAPPED_TO &Serial1  // change this line to map the remote_unit port to a different serial port
#define GPS_PORT_MAPPED_TO &Serial2  // change this line to map the GPS port to a different serial port
//#define GPS_MIRROR_PORT &Serial1 //3 // use this to mirror output from a GPS unit into the Arduino out another port (uncomment to enable)
#define OPTION_SEND_STRING_OUT_CONTROL_PORT_WHEN_INITIALIZING_STRING ("test\n\r")

#define LCD_COLUMNS 20 //16
#define LCD_ROWS 4 //2       // this is automatically set below for HARDWARE_EA4TX_ARS_USB and HARDWARE_M0UPU
#define LCD_UPDATE_TIME 1000           // LCD update time in milliseconds
#define LCD_HHMM_CLOCK_POSITION LEFT          //LEFT or RIGHT
#define LCD_HHMMSS_CLOCK_POSITION LEFT          //LEFT or RIGHT
#define LCD_ALT_HHMM_CLOCK_AND_MAIDENHEAD_POSITION LEFT
#define LCD_ALT_HHMM_CLOCK_AND_MAIDENHEAD_ROW 1
#define LCD_CONSTANT_HHMMSS_CLOCK_AND_MAIDENHEAD_POSITION CENTER
#define LCD_CONSTANT_HHMMSS_CLOCK_AND_MAIDENHEAD_ROW 3
#define LCD_BIG_CLOCK_ROW 4
#define LCD_GPS_INDICATOR_POSITION RIGHT //LEFT or RIGHT
#define LCD_GPS_INDICATOR_ROW 1
#define LCD_MOON_TRACKING_ROW 3                                   // LCD display row for OPTION_DISPLAY_MOON_TRACKING_CONTINUOUSLY
#define LCD_MOON_TRACKING_UPDATE_INTERVAL 5000
#define LCD_SUN_TRACKING_ROW 4                                    // LCD display row for OPTION_DISPLAY_SUN_TRACKING_CONTINUOUSLY
#define LCD_SUN_TRACKING_UPDATE_INTERVAL 5000
#define LCD_MOON_OR_SUN_TRACKING_CONDITIONAL_ROW 3                // LCD display row for OPTION_DISPLAY_MOON_OR_SUN_TRACKING_CONDITIONAL
#define SPLASH_SCREEN_TIME 3000

#define LCD_HEADING_ROW 0
#define LCD_HEADING_FIELD_SIZE 20
#define LCD_AZ_ONLY_HEADING_ROW 2
#define LCD_AZ_ONLY_HEADING_FIELD_SIZE 20
#define LCD_EL_ONLY_HEADING_ROW 3
#define LCD_EL_ONLY_HEADING_FIELD_SIZE 20
#define LCD_STATUS_ROW 1
#define LCD_STATUS_FIELD_SIZE 20
#define LCD_DIRECTION_ROW 2
#define LCD_HHMMSS_CLOCK_ROW 1
#define LCD_HHMM_CLOCK_ROW 1
#define PARKING_STATUS_DISPLAY_TIME_MS 5000

#define AZ_BRAKE_DELAY 3000            // in milliseconds
#define EL_BRAKE_DELAY 3000            // in milliseconds

#define BRAKE_ACTIVE_STATE HIGH
#define BRAKE_INACTIVE_STATE LOW

#define EEPROM_MAGIC_NUMBER 105
#define EEPROM_WRITE_DIRTY_CONFIG_TIME  30  //time in seconds


#if defined(FEATURE_TWO_DECIMAL_PLACE_HEADINGS)
#define HEADING_MULTIPLIER 100L
#define LCD_HEADING_MULTIPLIER 100.0
#define LCD_DECIMAL_PLACES 2
#endif //FEATURE_TWO_DECIMAL_PLACE_HEADINGS

#if defined(FEATURE_ONE_DECIMAL_PLACE_HEADINGS)
#define HEADING_MULTIPLIER 10
#define LCD_HEADING_MULTIPLIER 10.0
#define LCD_DECIMAL_PLACES 1
#endif //FEATURE_ONE_DECIMAL_PLACE_HEADINGS

#if !defined(FEATURE_ONE_DECIMAL_PLACE_HEADINGS) && !defined(FEATURE_TWO_DECIMAL_PLACE_HEADINGS)
#define HEADING_MULTIPLIER 1
#define LCD_HEADING_MULTIPLIER 1.0
#define LCD_DECIMAL_PLACES 0
#endif //!defined(FEATURE_ONE_DECIMAL_PLACE_HEADINGS) && !defined(FEATURE_TWO_DECIMAL_PLACE_HEADINGS)

#define AZ_POSITION_ROTARY_ENCODER_DEG_PER_PULSE 0.5
#define EL_POSITION_ROTARY_ENCODER_DEG_PER_PULSE 0.5

#define AZ_POSITION_PULSE_DEG_PER_PULSE 0.5
#define EL_POSITION_PULSE_DEG_PER_PULSE 0.5

#define PARK_AZIMUTH 360.0 * HEADING_MULTIPLIER      // replace the 0.0 with your park azimuth; azimuth is in raw degrees (i.e. on a 180 degree starting point rotator, 0 degrees = 360)
#define PARK_ELEVATION 0.0 * HEADING_MULTIPLIER    // replace the 0.0 with your park elevation

#define COMMAND_BUFFER_SIZE 50

#define REMOTE_BUFFER_TIMEOUT_MS 250
#define REMOTE_UNIT_COMMAND_TIMEOUT_MS 2000
#define AZ_REMOTE_UNIT_QUERY_TIME_MS 150         // how often we query the remote remote for azimuth
#define EL_REMOTE_UNIT_QUERY_TIME_MS 150         // how often we query the remote remote for elevation

#define ROTATE_PIN_INACTIVE_VALUE LOW
#define ROTATE_PIN_ACTIVE_VALUE HIGH

#define AZIMUTH_SMOOTHING_FACTOR 0      // value = 0 to 99.9
#define ELEVATION_SMOOTHING_FACTOR 0    // value = 0 to 99.9

#define AZIMUTH_MEASUREMENT_FREQUENCY_MS 100        // this does not apply if using FEATURE_AZ_POSITION_GET_FROM_REMOTE_UNIT
#define ELEVATION_MEASUREMENT_FREQUENCY_MS 100      // this does not apply if using FEATURE_EL_POSITION_GET_FROM_REMOTE_UNIT

#define JOYSTICK_WAIT_TIME_MS 100

#define ROTATION_INDICATOR_PIN_ACTIVE_STATE HIGH
#define ROTATION_INDICATOR_PIN_INACTIVE_STATE LOW
#define ROTATION_INDICATOR_PIN_TIME_DELAY_SECONDS 0
#define ROTATION_INDICATOR_PIN_TIME_DELAY_MINUTES 0

#define AZ_POSITION_INCREMENTAL_ENCODER_PULSES_PER_REV 2000.0
#define EL_POSITION_INCREMENTAL_ENCODER_PULSES_PER_REV 2000.0
#define AZ_INCREMENTAL_ENCODER_ZERO_PULSE_POSITION 0  // can be 0 to 4 x AZ_POSITION_INCREMENTAL_ENCODER_PULSES_PER_REV
#define EL_INCREMENTAL_ENCODER_ZERO_PULSE_POSITION 0  // can be 0 to 4 x EL_POSITION_INCREMENTAL_ENCODER_PULSES_PER_REV

#define SERIAL_LED_TIME_MS 250

#define DEFAULT_LATITUDE 40.889958
#define DEFAULT_LONGITUDE -75.585972

#define MOON_TRACKING_CHECK_INTERVAL 5000
#define MOON_AOS_AZIMUTH_MIN 0
#define MOON_AOS_AZIMUTH_MAX 360
#define MOON_AOS_ELEVATION_MIN 0
#define MOON_AOS_ELEVATION_MAX 180

 
#define SUN_TRACKING_CHECK_INTERVAL 5000
#define SUN_AOS_AZIMUTH_MIN 0
#define SUN_AOS_AZIMUTH_MAX 360
#define SUN_AOS_ELEVATION_MIN 0
#define SUN_AOS_ELEVATION_MAX 180



#define TRACKING_ACTIVE_CHAR "*"
#define TRACKING_INACTIVE_CHAR "-"
#define DISPLAY_DEGREES_STRING "\xDF"

#define INTERNAL_CLOCK_CORRECTION 0.00145

#define SYNC_TIME_WITH_GPS 1
#define SYNC_COORDINATES_WITH_GPS 1
#define GPS_SYNC_PERIOD_SECONDS 10  // how long to consider internal clock syncronized after a GPS reading
#define GPS_VALID_FIX_AGE_MS 10000  // consider a GPS reading valid if the fix age is less than this
#define GPS_UPDATE_LATENCY_COMPENSATION_MS 200

#define SYNC_WITH_RTC_SECONDS 59    // syncronize internal clock with realtime clock every x seconds
#define SYNC_RTC_TO_GPS_SECONDS 12  // synchronize realtime clock to GPS every x seconds

#define SYNC_MASTER_CLOCK_TO_SLAVE_CLOCK_SECS 10 // for OPTION_SYNC_MASTER_CLOCK_TO_SLAVE - use when GPS unit is connected to slave unit and you want to synchronize the master unit clock to the slave unit clock
#define SYNC_MASTER_COORDINATES_TO_SLAVE_SECS 20 // for OPTION_SYNC_MASTER_COORDINATES_TO_SLAVE - use when GPS unit is connected to slave unit and you want to synchronize the master unit coordinates to the slave unit GPS


#define ETHERNET_MAC_ADDRESS 0xDE,0xAD,0xBE,0xEF,0xFE,0xEE  //<-DON'T FORGET TO USE DIFFERENT MAC ADDRESSES FOR MASTER AND SLAVE!!!
#define ETHERNET_IP_ADDRESS 192,168,1,172  //<-DON'T FORGET TO USE DIFFERENT IP ADDRESSES FOR MASTER AND SLAVE!!!
#define ETHERNET_IP_GATEWAY 192,168,1,1
#define ETHERNET_IP_SUBNET_MASK 255,255,255,0
#define ETHERNET_TCP_PORT_0 23
#define ETHERNET_TCP_PORT_1 24
#define ETHERNET_MESSAGE_TIMEOUT_MS 5000
#define ETHERNET_PREAMBLE "K3NG"    // used only with Ethernet master/slave link

#define ETHERNET_SLAVE_IP_ADDRESS 192,168,1,173
#define ETHERNET_SLAVE_TCP_PORT 23
#define ETHERNET_SLAVE_RECONNECT_TIME_MS 250

#define POWER_SWITCH_IDLE_TIMEOUT 15  // use with FEATURE_POWER_SWITCH; units are minutes

#ifdef HARDWARE_EA4TX_ARS_USB
#define BUTTON_ACTIVE_STATE HIGH
#define BUTTON_INACTIVE_STATE LOW
#else
#define BUTTON_ACTIVE_STATE LOW
#define BUTTON_INACTIVE_STATE HIGH
#endif

/*
 *
 * Azimuth and Elevation calibraton tables - use with FEATURE_AZIMUTH_CORRECTION and/or FEATURE_ELEVATION_CORRECTION
 *
 * You must have the same number of entries in the _FROM_ and _TO_ arrays!
 *
 */

#define AZIMUTH_CALIBRATION_FROM_ARRAY {180,630}            /* these are in "raw" degrees, i.e. when going east past 360 degrees, add 360 degrees*/
#define AZIMUTH_CALIBRATION_TO_ARRAY {180,630}

// example: reverse rotation sensing
//   #define AZIMUTH_CALIBRATION_FROM_ARRAY {0,359}
//   #define AZIMUTH_CALIBRATION_TO_ARRAY {359,0}


#define ELEVATION_CALIBRATION_FROM_ARRAY {-360,0,360}
#define ELEVATION_CALIBRATION_TO_ARRAY {-360,0,360}

// example: reverse elevation sensing
//#define ELEVATION_CALIBRATION_FROM_ARRAY {0,180,360}
//#define ELEVATION_CALIBRATION_TO_ARRAY {180,0,-180}

#define ANALOG_OUTPUT_MAX_EL_DEGREES 180

#define EL_POSITION_PULSE_DEBOUNCE 500  // in ms


/* Pololu LSM303 Calibration tables
 *
 *
 * For use with FEATURE_AZ_POSITION_POLOLU_LSM303 and/or FEATURE_EL_POSITION_POLOLU_LSM303
 *


  Calibration values; the default values of +/-32767 for each axis
  lead to an assumed magnetometer bias of 0. Use the Calibrate example
  program to determine appropriate values for your particular unit.

  min: {   +59,    +19,   -731}    max: {  +909,   +491,    +14}
  min: {32767, 32767, 32767}       max: {-32768, -32768, -32768}

 */

#define POLOLU_LSM_303_MIN_ARRAY {+59, +19, -731}
#define POLOLU_LSM_303_MAX_ARRAY {+909, +491, +14}

#define AUTOCORRECT_TIME_MS_AZ 1000
#define AUTOCORRECT_TIME_MS_EL 1000 




/* ---------------------------- object declarations ----------------------------------------------


 Object declarations are required for several devices, including LCD displays, compass devices, and accelerometers
   

*/
/*
#if defined(FEATURE_4_BIT_LCD_DISPLAY) || defined(FEATURE_ADAFRUIT_I2C_LCD) || defined(FEATURE_YOURDUINO_I2C_LCD) || defined(FEATURE_YWROBOT_I2C_DISPLAY)
  K3NGdisplay k3ngdisplay(LCD_COLUMNS,LCD_ROWS,LCD_UPDATE_TIME);
#endif   

#ifdef FEATURE_AZ_POSITION_HMC5883L
  HMC5883L compass;
#endif //FEATURE_AZ_POSITION_HMC5883L

#ifdef FEATURE_EL_POSITION_ADXL345_USING_LOVE_ELECTRON_LIB
  ADXL345 accel;
#endif //FEATURE_EL_POSITION_ADXL345_USING_LOVE_ELECTRON_LIB

#ifdef FEATURE_EL_POSITION_ADXL345_USING_ADAFRUIT_LIB
  Adafruit_ADXL345_Unified accel = Adafruit_ADXL345_Unified(12345);
#endif //FEATURE_EL_POSITION_ADXL345_USING_ADAFRUIT_LIB

#if defined(FEATURE_EL_POSITION_ADAFRUIT_LSM303) || defined(FEATURE_AZ_POSITION_ADAFRUIT_LSM303)
  Adafruit_LSM303 lsm;
#endif

#if defined(FEATURE_AZ_POSITION_POLOLU_LSM303) || defined(FEATURE_EL_POSITION_POLOLU_LSM303)
  LSM303 compass;
  LSM303::vector<int16_t> running_min = {32767, 32767, 32767}, running_max = {-32768, -32768, -32768};
  char report[80];
#endif //FEATURE_AZ_POSITION_POLOLU_LSM303

#ifdef FEATURE_AZ_POSITION_HH12_AS5045_SSI
  #include "hh12.h"
  hh12 azimuth_hh12;
#endif //FEATURE_AZ_POSITION_HH12_AS5045_SSI

#ifdef FEATURE_EL_POSITION_HH12_AS5045_SSI
  #include "hh12.h"
  hh12 elevation_hh12;
#endif //FEATURE_EL_POSITION_HH12_AS5045_SSI

#ifdef FEATURE_GPS
  TinyGPS gps;
#endif //FEATURE_GPS

#ifdef FEATURE_RTC_DS1307
  RTC_DS1307 rtc;
#endif //FEATURE_RTC_DS1307

#ifdef FEATURE_RTC_PCF8583
  PCF8583 rtc(0xA0);
#endif //FEATURE_RTC_PCF8583

#ifdef HARDWARE_EA4TX_ARS_USB
  #undef LCD_COLUMNS
  #undef LCD_ROWS
  #define LCD_COLUMNS 16
  #define LCD_ROWS 2
#endif //HARDWARE_EA4TX_ARS_USB

#ifdef HARDWARE_M0UPU
  #undef LCD_ROWS
  #define LCD_ROWS 2
#endif //HARDWARE_M0UPU

#ifdef FEATURE_AZ_POSITION_A2_ABSOLUTE_ENCODER
  #define AZ_A2_ENCODER_RESOLUTION 32767 //36000
  #define AZ_A2_ENCODER_ADDRESS 0x00
  #define AZ_QUERY_FREQUENCY_MS 250
  #define AZ_A2_ENCODER_MODE MODE_TWO_BYTE_POSITION//|MODE_MULTITURN
#endif  //FEATURE_AZ_POSITION_A2_ABSOLUTE_ENCODER

#ifdef FEATURE_EL_POSITION_A2_ABSOLUTE_ENCODER
  #define EL_A2_ENCODER_RESOLUTION 32767 //36000
  #define EL_A2_ENCODER_ADDRESS 0x00
  #define EL_QUERY_FREQUENCY_MS 250
  #define EL_A2_ENCODER_MODE MODE_MULTITURN//|MODE_TWO_BYTE_POSITION
#endif  //FEATURE_EL_POSITION_A2_ABSOLUTE_ENCODER

#if defined(FEATURE_AZ_POSITION_A2_ABSOLUTE_ENCODER) || defined(FEATURE_EL_POSITION_A2_ABSOLUTE_ENCODER)
  #include "sei_bus.h"
  SEIbus SEIbus1(&Serial1,9600,pin_sei_bus_busy,pin_sei_bus_send_receive);
  //             (Serial Port,Baud Rate,Busy Pin,Send/Receive Pin)
  #define SEI_BUS_COMMAND_TIMEOUT_MS 6000
#endif
*/