-
Notifications
You must be signed in to change notification settings - Fork 3
/
Setup434_H2_ST7789_170x320.h
72 lines (58 loc) · 2.92 KB
/
Setup434_H2_ST7789_170x320.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
#define USER_SETUP_ID 434
#define ST7789_DRIVER // Configure all registers
//#define TFT_SDA_READ // Display has a bidirectional SDA pin
#define TFT_WIDTH 170
#define TFT_HEIGHT 320
//#define CGRAM_OFFSET // Library will add offsets required
//#define TFT_RGB_ORDER TFT_RGB // Colour order Red-Green-Blue
//#define TFT_RGB_ORDER TFT_BGR // Colour order Blue-Green-Red
//#define TFT_INVERSION_ON
//#define TFT_INVERSION_OFF
//#define TFT_BACKLIGHT_ON 1
//Pins ESP32-H2
#define TFT_CS 0
#define TFT_MOSI 25
#define TFT_MISO 11
#define TFT_SCLK 10
#define TFT_DC 1
#define TFT_RST 3 // Set TFT_RST to -1 if display RESET is connected to ESP32 board EN
//#define TFT_BL 2 // LED back-light
#define LOAD_GLCD // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
#define LOAD_FONT2 // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
#define LOAD_FONT4 // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
#define LOAD_FONT6 // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
#define LOAD_FONT7 // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:.
#define LOAD_FONT8 // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
#define LOAD_GFXFF // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
#define SMOOTH_FONT
////////////////////////////////////////////////////////////////////////////////////////////////////////////////
// Solution for Tasmota Luatos Core ESP32 C3
// Found : https://github.com/espressif/arduino-esp32/issues/9618
//
// 1. Edit C:\Users\username\Documents\Arduino\libraries\TFT_eSPI\Processors\TFT_eSPI_ESP32_C3.h and change
// #define SPI_PORT SPI2_HOST
// to
// #if ESP_ARDUINO_VERSION_MAJOR < 3
// #define SPI_PORT SPI2_HOST
// #else
// #define SPI_PORT 2
// #endif
//
// 2. Edit C:\Users\<username>\AppData\Local\Arduino15\packages\esp32\tools\esp32-arduino-libs\idf-release_v5.1-bd2b9390ef\esp32c3\include\soc\esp32c3\include\soc\soc.h
//
// Replace
// #define REG_SPI_BASE(i) (((i)==2) ? (DR_REG_SPI2_BASE) : (0)) // only one GPSPI
// with
// #define REG_SPI_BASE(i) (((i)==2) ? (DR_REG_SPI2_BASE) : (DR_REG_SPI0_BASE - ((i) * 0x1000)))
////////////////////////////////////////////////////////////////////////////////////////////////////////////////
// Still necessary for ESP32 S3
// FSPI / VSPI port (SPI2) used unless following defined. HSPI port is (SPI3) on S3.
//#define USE_HSPI_PORT
//#define SPI_FREQUENCY 20000000
//#define SPI_FREQUENCY 27000000
//#define SPI_FREQUENCY 40000000
#define SPI_FREQUENCY 80000000
//#define SPI_READ_FREQUENCY 20000000
// #define SPI_TOUCH_FREQUENCY 2500000
// #define SUPPORT_TRANSACTIONS